2012Â
http://www.jcverdier.com/ADSL/platineVintage.htmlÂ
Just a delight to use. With its presentation, sends the message home that it is all amount the music. Effortless, seamless, but experience is needed is setting up the thread. A real Goldilocks scenario of the thread being too loose, too tight or just right. Different thread tensions alternate how the motor and platter work together and change the speed. The objective is to get the correct speed with as little effect from the motor. .... Â
Â
Original design. Granito Model My version uses a motor only equipped for thread Granito base and solid aluminum billet armpod. The later newer motors are equipped now for belts too - but no one runs them this way that I know of. This decision was made imo to generate more sales as it is easier to setup. But imo the belt grip would play havoc with the motor / magnets marriage which was designed for thread. I would think that belt stretch and its physical changes with temp and humidity changes would also cause problems, and interfere with the natural braking action of the magnets. This is my opinion as mine is thread only. There is a greater learning curve involved with thread.Â
This is the only turntable I am aware of whose platter design includes both acceleration (inertia) and braking (natural forces from same pole magnets) to deal with the records behavior - going from soft to heavily modulated grooves. The motor design, like a marriage with the platter. Think of the childhood merry go rounds that once up to speed - even a little girl could keep them going. To understand how the motor and platter are like a marriage, one need only turn the motor off and the platter spins for 30 seconds with the thread attached. However cut the thread while the platter is turning, and the platter stops much quicker as the two magnets demonstrate their braking capability. Impressive to me is just the plain simplicity of design using physics to get the job done with a piece of string and magnets. I found it important in setup to have the thread positioned in a way that is the least intrusive on the platter; so as to allow the platter to not only do its job as designed; but to also provide the needed jolts as required from the motor to maintain speed stability.Â
 In my opinion - you will know when you have set it up properly because you are able to turn the motor off and on and also deflect the thread with your finger - as the records plays - and not affect the music delivery to your ears. I base this when compared directly to 15 IPS Master Tape dubs. In testing for accuracy I run both simultaneously with one lagging 10 seconds behind the other and switch between the two - compensating for gain as tape is a high level signal. When the thread is setup in this fashion there is minimal stress put on it. The current silk thread I am using has recently passed the one year mark. Overall Big Sound from a small piece of thread.Â
Some facts Magnetic bearing design. Brass colored rings are big shielded permanent magnets; same magnet poles repelling each other. The result is "levitation" the space you see between them. No thrust bearing involved. A central spindle bathed in a special oil keeps them aligned. For me personally I did not know what TT bearing noise sounded like until I heard music on a TT without a physical bearing. The plinth is made of Granito. Granito is not real granite but a non-resonant material that looks and feels like granite. A limited edition model.
 "Granito is a material composed by little pieces of marble of very different origin agglomerated inside a mold with cement. Machined and polished. The resonance of the plinth with its suspension is about 5Hz and it is well absorbed by the air cavities."Â
Mr. JC Verdier Note: Newer Platines are provided with a setup bearing. The manual is very clear on the setup bearing. It is just that - a setup tool only. COUNTERFEIT PLATINES Unfortunately there are non-authentic tables out there worldwide from 20 different counterfeiting makers. These tables are out there with people using them. If anyone is unaware of this, see the Platine Information on the JC Verdier website for more info.
http://www.jcverdier.com/ADSL/platineV.html]PlatineÂ
The only advice I can give is when buying a Verdier Platine you should be careful to ensure it is a real Platine, especially if buying privately. If you already have one and have doubts, check with an authorized dealer or J.C. Verdier company in France to ensure it is authentic. Â