Pure silver wire Swiss transformer, 240v to 120v. Plates, bolts, and all terminals treated with Total Contact. Mounted on BDR Cones in a 2" thick MDF cabinet with one Perfect Path Solutions Omega E-mat. Dedicated copper ground.

The Medusa power center is built on a custom Black Diamond Racing Black Beauty Shelf. Incoming power from 4 ga copper is hard-wired direct to a Jungson transformer with filter caps. Point to point Audio Consulting pure silver wire connects the Jungson to Oyaide and Synergistic Research Blue outlets strategically located on the four faces allowing short direct power to components from the centrally located Medusa.

Based on the Teres Audio turntable bearing, platter, and Verus Rim Drive Motor, the Carbon features a Black Diamond Racing carbon fiber plinth, arm base, and feet. The brass bearing screws directly into a large 4" diameter by 1.25" thick threaded BDR carbon fiber nut for extreme rigidity and vibration control. The Teres bearing is modified with a silicon carbide bearing and tungsten carbide thrust plate. The Verus motor is modified with a BDR Source Shelf base, Cones, and mini-Pits. 

2007 Conqueror. Leads modified with Active Shielding using Michael Spallone modified Synergistic Research MPC with upgraded caps and diodes hard wired. One Synergistic Research PHT on the arm, 2 ECT on the arm base.

0.4 mV output MC cartridge with body lightly painted with Total Contact, and with one SR Green Dream and one Black Beauty PHT. Pins and leads treated with Total Contact.

2018 Herron VTPH-2A phono stage with Synergistic Research Orange Fuse, 3 ECT, 2 Perfect Path Solutions Stop-Its, and all tube pins, transformers, and other items treated with Total Contact.

The Solution to turntable vibration control is a modular component rack. Top and bottom shelves are solid reinforced 4" thick concrete with a 2" deep sand bed cast into them. The middle component rack is 2" thick concrete. Legs of polished ABS are filled with concrete, with threaded inserts cast into them. Bottom footers incorporate BDR Cones and are height adjustable for leveling. Assembled on site due to its over 700 lbs total weight The Solution is bolted together for extreme rigidity. The granite machinists plate rests on a 2" deep sand bed.

2m Euphoria, grounded to dedicated Earth ground with all connections treated with Total Contact and supported with ceramic insulators.

Melody I880 with 4 JJ KT-88, 4 Sovtek 6SN7, and one D100 rectifier tube. Modified with one pair of input RCA converted to pre-out. The factory feet are removed. Three BDR Those Things on the inside of the bottom cover are screwed together through the bottom plate with three Round Things, with the cover sandwiched between them, and with a Cone screwed into the bottom of each.  The Cones are supported on Round Things on top of a Shelf, Cones, 150 lb granite plate, and Cones.

8 ft Element CTS with spades and Michael Spallone modified Tesla MPCs hard wired into the Medusa power conditioner with in-line Audio Consulting pure silver isolation transformer. All connections and transformer surfaces treated with Total Contact. Supported with Cable Elevators and ceramic insulators.

Talon Khorus with X crossover upgrade treated with Total Contact and Perfect Path E-cards. Synergistic Research Speaker Kit HFT treatment. On BDR Cones and Round Things.

2 Dayton subwoofer amps. Each one drives two 10" subs, wired in series for 16 ohms. Transformers, caps, resistors and all connections treated with Total Contact. Perfect Path Stop-Its on unused RCAs. Amps stack on each other with BDR Cones.

A Distributed Bass Array comprised of 2 Morel 10" drivers in sealed cabinets and 2 in ported cabinets. All covered in stained Rosewood veneer.

Every single component in The System is on BDR Cones- including even parts like the Audio Consulting transformers, Talon Khorus crossover networks, and the Medusa Power Center. Most components, such as the speakers, amp, phono stage, and turntable, are also on Round Things.

Level 2 HFT Room Treatment. Several ECT on Melody, Herron, Verus motor, and motor controller, and Conqueror arm. Two Green Dream and one Black Beauty PHT on the arm and cartridge. Orange Fuses in Melody, Herron, and Verus motor controller.

Several, located on the main electrical panel, Audio Consulting step down transformer, Talon Khorus speakers, and Medusa Power Center.

Located on the Medusa, SR Atmosphere interconnect, Verus motor, Herron phono stage, Talon crossovers, breaker panel, and Dayton amps.

Cable Elevators together with ceramic insulators on stands support all wire above the floor and maintain spacing minimizing field interference.

Resolution Reference .5 and Master Coupler power cords to the Herron and Oppo.

Power cord to the Melody integrated.

2 Fat Boy 2 foot power cords to the Daytons.

Extensively modified player on BDR Cones, with BDR Shelf and dive weights on top.

Ceiling mounted. With 10m cryo'd Cobalt HDMI.

Viewable 92x50  screen mounted in custom black velvet screen frame.

Half inch MDF window shutters for shutting out sound and light.

With weather stripping for sound control.

Owens Corning acoustic panels covered in Art Deco designer fabric for acoustic control in corners where walls meet ceiling and ceiling and walls come together.

Powerful handheld demagnetizer for demagnetizing records and cables, and charging Omega E Mats.

When used for movies, sits on top of the Oppo, with one ECT and one E-Card. Video out to projector via HDMI adaptor. Audio out to the integrated via mic to RCA adaptor.

Townshend Podiums are used under the Tekton Moab speakers. 

Duelund JDM Silver bypass caps, Jantzen Alumen Zcaps, Goertz Alpha Core inductors, and Path Audio resistors in crossover upgrade 5/15/21.