The compact disk player which carries legato linking conversion in addition to compact-disk turntable scheme.It asks for natural compact-disk play near a more nearly original music signal, and legato linking conversion is carried. A music signal is caught on a time base, it is what considered connecting a music signal data smoothly in time, and the signal currently recorded on compact disk is connected with legato linking conversion to origin using the function curve set up approach an original music signal. This has obtained the wave near an original music signal with few ringings.By realizing the waveform transmission excellent in this impulse response, the frequency component of 20kHz or more according to a 1/f damping characteristics will also be reproduced, and the soft natural music play is enabled.compact-disk turntable mechanism which moved the pickup and the spindle motor upwards is adopted as a mechanism part. This is enabled to hold a disk the whole surface from the bottom, and the unnecessary oscillation is suppressed low.The moment of inertia of the turntable became 3 times compared with the conventional scheme, is strong also to a load variation and has realized the stable rotation performance. The high speed pulse flow digital analog converter of original development is adopted as a digital analog converter. In this digital analog converter, the re-quatization noise is low-ized by operating a noise shaper on a high oversampling frequency called 384fs. Moreover, since a noise shaper degree can also be used by the sub- and a low degree by having raised the oversampling frequency, the influence on the tone quality resulting from an out-of-band noise, an analog low pass filter, etc. is suppressed. Furthermore, the influence of a Jitter is low suppressed in operating a master clock with a clock frequency as low as 16.93MHz.Moreover, since this digital analog converter has raised the duty which is a timing ratio of on/off of a 1-bit output from 50% to 100% and an Output voltage becomes twice by this, the audio output of the high SN ratio and the low distortion is obtained. The proprietary clean laser pickup is adopted as a pickup.In this pickup, by reduction of optical components, reduction of the aberration in an optical path, etc., the laser efficiency ratio was raised and signal reading of a low distortion is realized. Furthermore by adoption of a photodetector with built-in I/V head amplifier, or adoption of an Accu Focus system, a reading error and the influence of a Jitter are reduced. Moreover, the pickup body has adopted the highly precise engineering pickup body. Class-A operation FET buffer amplifier is adopted as an audio circuitry, and the influence of the load intensity of the equipment connected by low-power-output impedance-ization etc. is suppressed low. Furthermore, the variation of the power consumption at the time of an operation could be reduced by Class-A operation, and the low distortion is realized. In order to carry out thorough exclusion of the oscillation and vibration which have an ill effect on a tone quality, the newly developed acoustic shell construction is adopted and rigidity has become what was highly excellent in the vibration proof by using form roundish like a shell. The protein coating is given in the shell form where R with the loose under base at the bottom was attached. This shell form has an effect which diffuses the sound pressure of the interior and the exterior, is also forming the sub- chassis of a mechanism upper portion, and both side panels into shell form, and has eliminated the parallel side which is easy to generate a stationary wave as much as possible.Furthermore, the under base has a two-sheet structure and has a firm structure which allots the 2mm thickness griddle which gave the copper plating through the beam by 20mm thickness aluminum extrusion material on the under base at the bottom. A space is secured between the under bases of two more sheets, and the direct construction which is making it connect with the audio substrate of a upper curtate from the latest through the product-line material from the power transformer for audios downward, and shortest-izes a signal path is also pursued. Moreover, the insulator has also adopted the shell type insulator of metals shaving appearance, and is absorbing the extraneous vibration. A digital & servo, an analog, and three transformers of a digital-analog-converter independency are carried. Furthermore, 6 part 15 regulator was employed, it separated into six parts of + of a digital & servo, a servo drive, a digital analog converter, and an audio, -, and function logic diagram, and the power circuit has eliminated the cross interferencee. The newly developed discrete stream-composition power source is adopted as an audio circuitry. Moreover, the influence from other power sources is eliminated from the exclusive transformer using a rectifier circuit and the stabilized power source of a right-and-left independency to digital analog converters.A servo driving power supply is also using the digital output as the exclusive power source while it makes it become independent the object for turntables, and for [ other ] a drive and attains a stabilization.The brushless hall motor of starting torque 65 g-cm is adopted as the spindle motor supporting a turntable scheme. phi4.5mm very-thick shaft and the rotation performance conjointly stabilized in a load variation strongly are realized.Moreover, the pickup is driven by the silence linear motor servo mechanism, and has realized the rapid access.In order to tell an oscillation to neither a substrate nor a power-source part, no vibrating and absent-resonance-ization of a disk-drive mechanism are put into practice. The whole mechanism is covered and the adoption of a silence chassis which improves a vibration proof is begun,The unnecessary oscillation from an inside-and-outside part, such as piling up two heterogeneous metalses, and the lamisert Mechanism-base which carried out molding by the special resin, and also the turntable base carrying out mechanism-chassis mounting through a coaxial suspension, and making them into a double float structure, is reduced. The balance output which cannot be easily influenced by an exogenous noise is carried.The polar attached-indicator OFC4 core power cord which divided the cable into the digital & servo and only the analog is adopted.The aluminum panel stabilizer which improved rigidity and a vibration proof is adopted.The display-device off switch point which prevents a scanning noise is carried. Moreover, the clean microcomputer is carried (backup correspondence).Digital one / analog circuit changing switch is carried (backup correspondence).The non-magnetic-material gilding RCA output jack is adopted.Moreover, OFC (oxygen free high conductivity copper) is adopted as an analog substrate. Rating of a mode Form Compact disk player Pickup 3 beam semiconductor laser scheme Frequency characteristic 2Hz - 20kHz SN ratio (EIAJ) 115dB or more Dynamic range (EIAJ) 99dB or more Channel separation (EIAJ) 110dB or more Wow and flutter (EIAJ) Below a limit of measurement (±0.001%W.PEAK) THD (EIAJ) 0.0015% or less Output voltage 2.0Vrms The number of channels Two channels (stereo) Digital output Coaxial output: 0.5 Vp-p/75ohm Optical power: -15dBm--20dBm (wavelength of 660nm) Power source AC100V, 50Hz/60Hz Power consumption 18W Dimensions Width 440x height 151x depth of 433mm Weight 20kg Adjunct Wireless remote control

In the inside of the certain requirements of "Integrated Amplifier in the technician of Pioneer. The highest-class Integrated Amplifier which continued warming the idea ", six years supposing it expressed our will to the maximum extent, adopted the circuit design simple for "a straight sound", and also incorporated all the technologies that it can have, such as thought, technologies, etc., such as Exclusive C7, and was born. The symmetrical twin monophonic structure is adopted. Focusing on a central power-source part, the shielding TAP box which summarized input block of a small signal system right and left in the power block and the center of back of a large-current circuitry has been arranged, and the separation which was excellent with the symmetrical structure which considered the right-and-left channel circuitry as the independent stream composition is gained. Moreover, it equalizes to environments, such as a temperature in the main unit which influences the length of right-and-left signal path length, or not only the stream composition of parts but an operation of an element or a circuitry, a magnetic-field distribution, an oscillation, and the occurrence of the electric and mechanical property error on either side is also held down. The merit of the balance which linked two amplifier directly and was excellent, and the Integrated Amplifier from which compactness is obtained is as it is,In order to attain the purpose of the separate amplifier of operating the circuitry where the roles of a voltage amplification and current amplification differ proper, respectively, the pre power isolated rate structure is adopted. An included preamplifier circuitry (from an input terminal to the voltage amplification stage) is shielded for a volume with a nonmagnetic aluminum TAP box,Furthermore, this TAP box has adopted the floating structure supported with a chassis through vibration suppression rubber, the power-source part also considered the pre part and the power part as the independent stream composition from the rectifier circuit, and thorough separation-ization is realized. Also electrically and physically an isolated rate is formed so that a delicate input signal may not cause the tone-quality failure by the circuitry interference from a power part, a variation of a power-source part, and oscillation by this, and it has a structure which can also be called the separate amplifier in a set. The advanced direct construction into which the direct construction which shortens a signal path as much as possible was developed further is carried. The signal changeover relay and the volume unit were controlled from the front panel just behind the input terminal, and input block is arranged back. Furthermore, much more shortest-ization is realized by having arranged 16 power transistors of a power block back collectively. From input block, a signal is direct led to power amplifier, and batch processing is carried out in amplifier back, and it has attained large shortening of the path between Puri Power who became a noise source easily, and between power speaker terminations. Moreover, it is that the buffer amplifier which the inside of an input circuit also arranged the signal changeover relay immediately after the input terminal, and has improved the crosstalk between each source greatly, and also was mounted on the same substrate as a relay carries out a low-impedance drive,The outstanding channel separation by low-impedance-izing of a circuitry is realized. A power amplifier part is expanding the original super linear circuit which carried out the pure Class-A operation and which Pioneer has cultivated to the last stage of a large current, in spite of final-stage a unreturned stream composition, attained 0.05% of low distortion, and also has realized the high dumping factor 200. The one molding silence chassis of the newly developed high precision is adopted as a chassis. The torsion-proof property, the impact property-proof, and the newly developed special resin material excellent in secular change are developed and adopted. The internal and external oscillation is efficiently reduced by making it the form which suited each block at the same time this supports a main unit firmly. An electromagnetic-induction noise and a magnetic distortion are sharply controlled for nonmagnetic. The stack type electrolytic capacitor of a low flux noise developed in pure first class amplifier is adopted as a power-source part, and capacity sufficient with low flux density and a power transformer with the outstanding regulation property are adopted, and the flux noise is stopped low. The handmade attenuator type with the same basic structure as what was adopted as Exclusive C7 is adopted as a volume. Unlike that to which it constitutes from the carbon resistor and high precision contact which selected one step carefully at a time, and a sound volume is changed by general slide resistor, there is little influence by a temperature, humidity, etc., the level difference of the tone-quality transition and right and left by contact resistance is eliminated, and the stable control is enabled. In order to pierce through the design of a tone-quality first priority, it is dared to omit attached functionalities, such as a tone control, a balance, a loudness, and the speaker output is also made into one line. While this suppresses the delicate influence by the circuitry or switchpoints, shortest-ization of the event of a product-line step or a signal path is enabled. Moreover, the grounding side of each input source was also changed simultaneously, and the separate grounding design which eliminates the signal interference between the connection assemblies from the grounding side is adopted. The Phono equalizer has 1 chip dual FET input composition. The input terminal carries one balance input and has adopted the reliable gilding termination as all the terminations. Moreover, the speaker terminal has adopted the large-sized vice type. The mass very-thick type OFC power cord is adopted. This power cord has adopted the scheme pulled out out of a case from just under a power transformer, and is reducing the influence of external noise. the high-class type carried out aluminum Naked shaving appearance, and the rotary knob, and the resistor and capacitor which were selected carefully are adopted. The fraction which makes the generated heat absorb by having carried out the intensive placement of the power transistor, and the fraction diffused effectively were distributed, and the new heat-dissipation structure where consideration was carried out to the location of a heat sink, form, and the path into which air flows is adopted. Moreover, the new type which changes the length of a fin and suppresses a vibration is adopted as the heat sink made from aluminum. Rating of a mode Form Stereo Integrated Amplifier Output power (both channel drive) 35W+35W (8 ohm, 20Hz - 20kHz, 0.05%) 70W+70W (4ohm) Dumping factor (8ohm) 150 (20Hz - 20kHz) 200(1kHz) Input sensitivity/impedance Phono man month: 2.5mV / 50kohm compact disk, Tuner, Line, Tape:150mV /, 50kohm Balance: 150mV/600 ohm Phono maximum permissible input man month: 150mV (1kHz, 0.05%) An Output voltage/impedance Tape Rec: 150mV / 1kohm Frequency characteristic Phono man month: 20Hz-20kHz±0.2dB compact disk, Tuner, Line, and Tape:1Hz-150kHz+0 -3 dB S/N (IHF, A network) Short circuit Phono MM:87dB compact disk, Tuner, Line, Tape: 109dB Supply voltage AC100V, 50Hz/60Hz Power consumption (Electrical Appliance and Material Control Law) 220W Dimensions Width 440x height 198x depth of 480mm Weight 28.8kg

The high-class stereo player system announced at the Exclusive P3 and concurrent term. For investigation of the musicality put into practice like P3, the technical know-how was poured in and it was manufactured by an one-set one-set handmade. EM-10 is adopted as a phone motor part. In EM-10, the linear torque hall motor of the coreless slotless structure which cocking does not generate is adopted, and powerful starting torque (3 kg-cm) has been obtained. Moreover, in order to obtain the stable rotation, the ヤジロベー type SHR scheme (Stable hanging rotor) was adopted as the bearing structure, the reduction of side pressure added to bearing and the centroid of the rotation fraction were made low, and the rotation performance of 0.002% of a rotational frequency precision is realized rotation unevenness 0.007%. EA-10 is adopted as a tone arm. In EA-10, the level good transformation oil dumping organization in which the silicon oil of the robustness was used is adopted, and cross modulation distortion generated at the time of the improvement in trackability and a large swing play of a bass region is reduced sharply. Moreover, it can perform easily becoming dumping-off and taking a longitudinal balance correctly by rotating an adjust ring. In order to make the mechanical impedance of a tone arm make it flat, it carried out by having repeated the analysis and audition of the oscillation mode of all fractions, and the straight tapered pipe of the carbon fiber of head shell one is adopted. This holds down an oscillation of each fraction covering a detail, and the possible of the play is carried out by the tone quality broadly stabilized from man month to MC. Moreover, in order to enable a using of a commercial head shell, S character type universal arm pipe is also equipped, and it enables it to correspond to almost all cartridges. The slit scheme laminating solid board of the absent resonance was used, the unnecessary oscillation was prevented to the player, and the low centroid type insulator strong against a howling is attached to the cabinet from the upper part inside a main unit. Moreover, finish serves as a simple design which is the Andes rosewood native wood finish and combined smoked acrylics ふ - of 5mm thickness. Rating of a mode Form Cartridgeless player system Motor synopsis Linear torque DC hall motor Bearing structure SHR scheme Drive system Direct-drive Control system Quartz PLL Rotational frequency 33 1 / 3 or 45rpm Rotational frequency precision 0.002% Rotation unevenness 0.007% (WRMS, the FG method) 0.015% (WRMS, the Japanese-Industrial-Standard record method) S/N 78dB(DIN-B) Starting torque 3kg-cm Opposite load characteristics With no rotational frequency transition to 540g of stylus forces Startup property 0.9 second Turntable 31cm aluminum low voltage casting, weight of 2.8kg (included vibration proof material) Inertial mass 680kg-cm2 (it is an included about a motor rubber sheet) Form Dynamic balance type twin pipe exchange system a straight-with integrated head shell pipe -- and S character type universal pipe Arm effective length 282mm Overhang 12.5mm Tracking error + 1.85 degrees-1.10 degrees Stylus-force adjustable range 0-3g (0.1g step) Conformity cartridge self-weight 4g-52g (wait exchange system) Height adjustable range ±3mm Output code With a low-impedance gilding plug (oxygen-free-high-conductivity-copper line) Base attachment Collet chuck scheme Braking part The low-pass brake style by silicon oil (Dumping fator variable scheme) An attached organization Direct lever scheme anti skating Silicon oil dumping scheme arm lifter Cabinet The Andes rosewood native wood finish Hood 5mm thickness acrylics smoked 貼合せ hood Hinge A free stop, a removable Insulator The insulator by a coil spring and rubber (low centroid structure) A brake with a quick stop An electron, a mechanism combined use brake Manual operation button A feather touch, the short stroke push SW Power source AC100V, 50Hz/60Hz Power consumption 9W Dimensions Width 550x height 245x depth of 415mm Weight 30kg

The FM/AM tuner developed aiming at the high sensitivity tuner while adopting many systems for raising a tone quality. DDDtypeIII to which DDD(digital direct decoder) TypeII was made to upgrade further is adopted. The main detection scheme was changed into the PLL (phase locked loop) scheme from the conventional pulse-count scheme, this became unnecessary the 2nd IF stage, the signal system was made simpler, and S/N is improved. In order that a long-distance reception and a neighboring office reception may also maintain a high sensitivity, ARTS (Active RealTime Tracing System) is carried. By this scheme, since a narrow filter follows in footsteps according to the signal for which it wishes, the strength of wide both filters can be acquired as it is narrow, and the distortion and the performance of selectivity are improved. Moreover, since it is not a feedback but feed forward, the stability and the non spectrum of a circuitry system have been realized. In order to eliminate the oscillation and vibration which are connected distorted, while raising an intensity by adopting the honeycomb chassis excellent in the periodic-damping property, the good damping characteristics has been acquired also from the outside, such as sound pressure, to the oscillation. Moreover, since a local block is a high sensitivity, and a minute oscillation also changes it to sound energy about an oscillation and it leads to a tone-quality failure, it filled up the local block with the resin and has prevented the tone-quality failure. Furthermore, the large-sized insulator currently used also for compact disk or amplifier is adopted as the oscillation from the outside, and the unnecessary oscillation from a lower part side is suppressed. Two FM antenna terminations are carried, an antenna is switched towards each office to hear, and proper use is possible. The random pre-set which can be preset to 24 games is carried in all. Automatic tuning level can be chosen as field strength in three steps in all. It is possible at manual tuning to receive a radio wave still weaker than automatic tuning level. Since a broadcast station can be called to the sequence which carried out memory whenever it carries the program memory functionality and a power source repeats OFF-ON-OFF, if it uses together with an audio timer, the absence sound recording of three broadcasts by which memory was carried out can be carried out in order. The MPX mode functionality is carried and three positions of a stereo / monophonic recording / high blend can be chosen according to field strength. The sound recording of proper level is simply possible by building in the submission signal of about 330Hz and a 50% modulation which is the reference level for FM broadcasts, and uniting the level meter of the deck with -2dB. Rating of a mode Form FM/AM digital synthesizer tuner Received frequency 76MHz - 90MHz Practical speed mono: 9.3dBf (0.8 microvolt/75 ohm) SN ratio mono:100dB stereo:92dB THD mono: 0.008% (100Hz), 0.005% (1kHz), 0.01% (10kHz) stereo: 0.01% (100Hz), 0.008% (1kHz), 0.05% (10kHz) Capture ratio 0.8dB Effective selectivity 90dB(400kHz) 60dB(300kHz) Stereo separation 1kHz:70dB 20Hz - 20kHz : 54dB Frequency characteristic 20Hz-15kHz+0.2 -0.8 dB Image stonewalling ratio 80dB IF stonewalling ratio 100dB Spurious stonewalling ratio 80dB AM supression ratio 70dB Subcarrier supression ratio 65dB Muting operation level 25.2dBf (5 microvolts/75 ohm) Antenna input impedance 75-ohm unbalance type Received frequency 522kHz - 1629kHz Practical speed (attached loop antenna) 150microvolts/m Selectivity ±9kHz : 40dB SN ratio 50dB Image stonewalling ratio 40dB IF stonewalling ratio 60dB Antenna Loop antenna (adjunct) An Output voltage/impedance FM (100% modulation): 650mV/900 ohm AM (30% modulation): 150mV/900 ohm Supply voltage AC100V, 50Hz/60Hz Power consumption (Electrical Appliance and Material Control Law) 18W Dimensions Width 420x height 84x depth of 316mm Weight 4.6kg

Denon DL-S1 Specifications Output: 0.15mV Output Impedance: 40ohms Stylus: special elliptical tip Coil: copper (6N) and solid gold Frequency range: 20Hz-70kHz Tracking force: 1.1-1.5g Compliance 14x10-6cm/dyne Weight: 7.0g

Description The housing of the Audio Technica AT33E is precision aluminium-alloy die-cast, sandwiched between hard resin plates to ensure substantial Q-damping effect Specifications Frequency response: 15-50,000Hz Output voltage: 0.5mV Tracking weight: 1.6-2.0g Weight: AT33E 7g

DENON AU-S1 AU S1 AUS1 STEP UP TRANSFORMER FOR MOVING COIL CARTRIDGE Considered one of the best step-up MC transformers in the world at any price, the Denon AU-S1 also continues to be affordable. Made from high rigidity, non-magnetic aluminum for isolation and non-resonance, the Left and Right channels are independent from the unit's hollow structure. Large-sized 78 perm-alloy cores are used for near zero magnetostriction and highest fidelity. The Denon AU-S1 is optimal for 3 - 40 ohms correspondence. Denon AU-S1 MC Step-up Transformer Specifications - Boosting ratio: 1:13 - Load impedance: 47k ohms - Frequency range: 10Hz-80kHz - Size: W150 x H70 x D175mm - Weight: 3.2 kg (7.1 lbs.)

The twin pipe tone arm of the arm exchange system adopted as Exclusive P10. The level good transformation oil dumping organization using the silicon oil of hi-reliability is adopted, and cross modulation distortion generated at the time of the improvement in trackability and a large swing play of a bass region is reduced sharply. Moreover, it is possible to become dumping-off by rotating an adjust ring and to take a longitudinal balance correctly. The product made from carbon fiber straight tapered pipe of head shell one which made the mechanical impedance of the tone arm make it flat is adopted. Moreover, in order to enable a using of a commercial head shell, the S character type universal arm pipe is also equipped. There was a straight pipe arm as an option. Rating of a mode Form Tone arm Synopsis A dynamic balance type, a pipe exchange system straight pipe And S character type pipe adjunct Arm effective length 282mm Overhang 12.5mm Tracking error angle + 1.85 degree--1.10 degree Stylus-force adjustable range 0-3g (0.1g step) Conformity cartridge self-weight 4g-35g (head shell not included) Height adjustable range 46.5mm - 80mm Output code With a low-impedance oxygen-free-high-conductivity-copper line gilding plug Base attachment Collet chuck scheme Braking part The low-pass brake style by silicon oil (dumping factor variable scheme) An attached organization Direct lever scheme anti skating Silicon oil dumping scheme arm lifter Weight 2.5kg Straight pipe arm EP-01 (X2)

The speaker system which made the unit highly efficient.

The speaker system which made the unit highly efficient by the technique of "Driving the diaphragm of a light weight and a high rigidity in the magnetic circuit of high flux density", and carried out thorough investigation of "the absent-resonance-izing of a systemwide." The basic technique and new technology which were cultivated by the development of a TAD (Technical Audio Devices) unit are supplied, and it is made to complete. Full mid ship mounting which supports all units in parts other than a baffle is adopted. The Woofer which generates the biggest oscillation is firmly fixed to the enclosure base (sole plate) which put the griddle of 2.5mm thickness between two apitong plywood of a high rigidity with the frame of aluminum die-casting. Moreover, the mid range and the tweeter are fixing the magnetic-circuit rear to the inner baffle of apitong PCB which sandwiched high-density needle-leaf tree particle board with the apitong board firmly. An interference of each unit decreases by leaps and bounds by this full mid ship mounting, and it has an enclosure structure which pulls out an original sound of a unit. Furthermore, since the basic thought of "not making an excessive sound" is put into practice, the absent-resonance technology is supplied to the systemwide. The baffle board, the back board, and the top plate have high-rigidity-ized the whole enclosure combining the high-density needle-leaf tree particle board from which density differs mutually. Moreover, the magnetic circuit of a Woofer, a mid range, and a tweeter carries out the copper plating treatment of the iron material, distributes the resonance point, and is decreasing the unnecessary oscillation of a unit sharply. Furthermore, the network also made vibration proof material intervene between a substrate, a cabinet and a substrate, and each element, and the fine vibrating of a network part has canceled distortion generated owing to. A 30cm cone type Woofer is adopted as low-pass. The phi165x24mm large-diameter strontium ferrite magnet has realized high flux density of 14000 gauss. Furthermore, a magnetic circuit carries out a copper plating, is reducing a magnetic distortion, and has obtained the pure tone quality. For a diaphragm, the new-materials new improved carbon graphite is used in new curve form, and the acoustic feature is further raised to it. Moreover, technologies, such as adoption of LDMC (Linear Drive Magnetic Circuit) which stops the amplitude distortion of a voice coil, are supplied. A 6.5cm dome shape squawker is adopted as the mid range. With the phi156x17mm strontium ferrite magnet, the magnetic circuit which realized flux density of 16000 gauss is adopted. And the copper plating treatment is carried out to iron material, and a magnetic distortion is reduced. The ceramic graphite is adopted as a diaphragm and the tone quality in which the tangential edge, the edgewise voice coil, etc. were excellent conjointly is realized. The dome shape tweeter of 2.5cm is adopted as the high region. The phi85x20mm strontium ferrite magnet is adopted as a magnetic circuit, and flux density of 20000 gauss is realized. Moreover, the copper plating is given in order to suppress a magnetic distortion. The shaping and the newly developed ceramic graphite of 99.99% of the ceramics-ized purity are adopted as a diaphragm, without using a binder and no base material for a graphite with the crystal structure which made the carbon atom arrange in two dimensions. In addition to the element placement which stops the crosstalk of each element to the minimum, the calking product line not using a solder etc. fully examines a circuitry structure, an element, and a layout in a network, and puts into practice low-loss-izing and low crosstalk-ization among it. Absent-resonance thought is taken in by the optional exclusive speaker base, and the laminating structure of high-density apitong PCB almost equivalent to S-3000 is used for speaker base CP-3000. Furthermore, since it can be used with a firm hexagon-headed bolt, linking directly firmly with mid ship mounting of S-3000, the Shindo morality in a setting status has been improved sharply. Rating of a mode Scheme 3 ways, 3 speaker bass-reflex scheme, and a bookshelf type Unit For low-pass: 30cm cone type For mid ranges: 6.5cm dome shape For high regions: 2.5cm dome shape Impedance 6ohms Play frequency band 25Hz - 40000Hz Output sound pressure level 90dB/W/m The maximum input 180W(EIAJ) Cross over frequency 450Hz, 3500Hz Dimensions Width 410x height 725x depth of 360mm Weight 47kg Option: Speaker base CP-3000 (an It is 1 set in two sets, 60,000yen) Dimensions Width 436x height 200x depth of 340mm Weight 18kg