Townshend Audio Seismic 'Low frequency' Isolation Pods from 3Hz and up on all planes any sizes 1-200kg free worldwide shipping

TOWNSHEND AUDIO SEISMIC ISOLATION PODS: FOR ALL COMPONENTS, HEIGHT ADJUSTABLE  Set of 4  SEISMIC ISOLATION PODS (feet, footers) Any Sizes AA - A - B -C - D - E - F (1Kg-200Kg) 
MADE IN THE UK
Seismic Load Cells™ are very ‘soft’ and allow free movement in all three dimensions; up/down, left/right and back/forth. This unique solution blocks all deleterious vibrations from 3Hz upwards and from all directions. As the frequency increases, the isolation progressively increases, ensuring that virtually no vibration can pass from and to the suspended equipment. As each hi-fi component is isolated, the sound progressively improves. Eliminates structure-borne feedback between speaker and vibration-sensitive equipment by fully floating your whole Hi-Fi System independently from the speakers and the floor. Townshend has devised a complete solution that allows this to be done in an optimum way. 

• Enhances clarity throughout the whole frequency range.
• Improves bass definition.
• Produces a wider and deeper sound stage.
• Neighbour friendly high level listening.

Positioned under any piece of equipment, four Seismic Isolation Pods will dramatically improve the sound by breaking the acoustic connection between the audio system and structural vibrations in the room down to 3Hz, whereas other isolation products on the market are only extending down to around 40Hz.

The Seismic Isolation Pod is a Seismic Load Cell™ with a circular foot attached to the lower-end cap for stability. The height may be adjusted by turning the top end cap, which allows easy levelling of audio equipment placed on a set of four Pods. There is a soft felt protective piece on the top and bottom faces of the end caps to allow for easy positioning and to prevent scratching.

The singular Seismic Isolation Pod is available with seven different weight capacities, ranging progressively from 1kg up to 64kg. Depending on the weight of the device, they can be used in sets of four, eight or more to isolate any piece of equipment of any weight from any vibration. 


(A) Orange 1kg - 12KG (B) Yellow 12kg - 20kg (C) Green 20kg - 40kg (D) Blue 40kg - 80 kg (E) Silver 80kg - 120kg (F) Gold 120kg - 200kg 
For asymmetric components such as a valve (tube) amplifier with the transformers at the rear, different load capability Seismic Load Cells™ can be used to balance the load.

At Townshend Audio, we understand that every item of hi-fi equipment has unique characteristics and requirements when it comes to load cells. We recognize the importance of selecting the right load cell to ensure optimal performance and maximize the potential of your speaker or audio equipment.

Our expert team is dedicated to providing personalized guidance and support throughout the process. By carefully assessing the mass and specific needs of your equipment, we will tailor our recommendations to guarantee the creation of the ideal rated load cell for you. Our goal is to optimize the performance and ensure a seamless integration between your equipment and our load cells.

Trust Townshend Audio to provide you with the expertise and guidance necessary to select the perfect load cell for your specific setup. Experience the difference that a precisely matched load cell can make in elevating the performance and sonic clarity of your hi-fi system.

Positive Feedback: Attack of the PODs!

"No, they are not from Mars! They are from London: Designed, constructed, and shipped from London, England by the brilliant Max Townshend to American audiophiles like us, The PODs isolate your gear like it was suspended in outer space. They allow both tube and solid-state gear to bloom in extraordinary ways. At $675 for a set of 4 Seismic Pods, tailored in weight to your specific piece weighing from 4-500 pounds, you will achieve resonance control you only dreamed of in the past! You can adjust the level as well! The Pods are a sonic miracle, and the best footers I know of in the here-and-now for maximizing the sound of valuable audio gear.

The biggest improvement I heard was with phono, specifically the E.A.R. 324 Solid State Phono Stage. I have tried numerous expensive tweaks under this mainly transformer coupled unit to enhance its sound, with only negative effect. With the Pods, it blooms and breathes like protoplasm itself has been infused into the unit. If you own a 324 and are reading this review, run, do not walk, to your nearest Townshend dealer and buy a set of Type A Seismic Pods!! You will achieve nirvana, and then some...
 An entire layer of grunge is removed with the Seismic Pods, as easily as opening a cardboard box. The build quality is first-rate, and they look sharp under anything silver or black. Each Pod even has soft ends to prevent scratching of the gear or table."

Townshend Seismic Isolation Pods are now available and are a true masterpiece of isolation technology and tremendous enhancement of sonic neutrality preventing floor born feedback. I think that they are amazing. They are priced right, and perform at many times their cost! Fabulous under solid state and tube gear, they are the best individual support devices I have heard to date. Like all devices of this nature, your results may vary from mine, but I sincerely doubt it! .....A keeper! My highest buy recommendation!"

N.B: Different spring types are required depending on the isolated unit's weight. Please see the table in the image gallery. You will need to divide the max weight of the unit being isolated by the number of pods you wish to use to determine the ’Load Cell’ required. For example, if your amplifier weighs 8KG and you intend to use four pods, then you will require Load Cell ’Type A’ as each spring type A pod can handle between 2 to 4 KG of weight.

Why we don't use spikes, balls, pucks or exotic stuff:

Rigidly spike or cone-mounted speakers transmit energy into the floor, radiating vibration throughout the room and, ultimately, through your rack and into your equipment. This seriously degrades performance as described above. Spike and cone-mounted speakers cause the whole room structure to vibrate, often resulting in an unrealistic boomy bass whilst masking subtle detail. Further, this unwanted structural vibration can seriously irritate your neighbours.

The critical component is the Townshend Seismic Load Cell™. The Seismic Load Cell™ consists of a high-quality alloy steel compression spring surrounded by a flexible synthetic rubber jacket with two end plates. Screw threads in each plate facilitate height adjustment and provide attachment points. A movement-sensitive, air-resistance damper rapidly dissipates low-frequency oscillation caused by disturbing the suspended equipment.

For nearly five decades, the team of highly qualified engineers at Townshend Audio, led by Max Townshend, have been working towards building the hi-fi system of your, and let's be frank, their dreams. Their quest is to find the best solution for every problem in the audio replay chain and build the ideal high-fidelity music reproduction system guided by common sense and sound engineering practice. To create this system, they had to re-visit almost every component, from source to speaker. Along the way, they encountered many unproductive dead-ends and established that no single technology or silver bullet could transform an ordinary hi-fi into an excellent one. By taking a rigorous approach to the design of every component in the system, the result is an exceptional music system. It has been highly praised as the best system ever heard by many discerning listeners and respected critics, including a number of professional soloists and orchestral players. Along the path of discovery Townshend have developed several components and techniques that are indispensable in the system and have been shown to enhance other high-end audio systems. www.townshendaudio.com

Made in the United Kingdom
1)Audiogon Seismic Pod thread
2)Audiogon Seismic Podium thread
3)Audiogon Seismic Podium thread
4)All threads on Audiogon